FTQN-2 Bridge Deflection Detector

The FTQN-2 Bridge Deflection Detector is used for measuring static and dynamic deflection, impact coefficient, power spectrum, and interval frequency of various bridges; monitoring low-frequency vibrations and displacements of large structures, etc. It provides accurate data for bridge construction, supervision, acceptance, and inspection departments, effectively guiding their work.

The FTQN-2 Bridge Deflection Detector uses a long-distance non-contact photoelectric conversion method to measure the dynamic and static deflection curves of bridges. It innovatively integrates optical path analysis and image acquisition, adopting a one-target-two-light design with dynamic precision range control to flexibly adapt to various customer and on-site needs. The powerful processing software can derive the impact coefficient of loads and the distribution of internal structural forces from dynamic curve numerical analysis, helping to identify weak points of the bridge and the integrity of the structure. It is a rare and practical bridge inspection device.

I. Instrument Principle:

The FTQN-2 Bridge Deflection Detector fixes a specialized target to the measurement point of the bridge, integrating the target with the bridge to form resonance. It converts bridge vibrations into light source vibrations of specific wavelengths. Through an optical analysis system, the light signal to be measured is analyzed and transmitted to an industrial CCD. By detecting changes in the central coordinates of the target's image on the CCD, the longitudinal and lateral displacements of the bridge under load and their time-response curves can be measured. The system's K-values (Kx, Ky), which represent the actual displacement value per pixel on the CCD, can be calibrated before measurement.

II. Application Areas:

1.Bridge construction control monitoring;

2.Static and dynamic load testing of existing bridges;

3.Bridge completion acceptance and appraisal;

4.Inspection of special bridges such as floating bridges and suspension bridges;

5.Deformation monitoring of beams and columns in large-span structures;

6.Low-frequency vibration monitoring of large structures;

7.Deformation and displacement monitoring of high-rise buildings;

8.Deformation and vibration displacement monitoring of dams and docks;

9.Vibration deformation detection of large piers, drilling platforms, etc.;

10.Load displacement detection of crane arms and booms.

III. Product Features:

1.Solves the issue of separated optical path analysis and image acquisition, improving detection accuracy and system stability;

2.Detection based on photoelectric conversion principle,不受現場環境及橋型限制，適應能力強;

3.Non-contact, long-distance, high precision, scientifically efficient design principle;

4.Dynamic precision and range, adaptable to various bridge types, on-site conditions, and customer needs;

5.Industrial area array CCD, enabling two-dimensional deflection measurement in a single instance;

6.One-target-two-light design,適應不同檢測距離及惡劣環境需要;

7.Automatic calibration, avoiding human error and saving manpower;

8.Real-time display of measurement data, automatic saving, highly intelligent;

9.Wireless remote control target,自帶高容量鋰電，高效輕松檢測.

IV. Technical Parameters:

1.Detection method: Photoelectric image method;

2.Measurement parameters: Single-point dynamic, multi-point static;

3.Detection distance: 500m;

4.Detection range: 0.8m;

5.Measurement accuracy: 0.1mm (at 50m);

6.Sampling frequency: 100Hz;

7.Frequency response: 50Hz;

8.Recording time: Can be set to any duration;

9.Transmission interface: USB;

10.Calibration method: Automatic calibration;

11.Target configuration: Remote control, built-in lithium battery, 10-hour battery life;

12.Battery capacity: Near light operable for 20h, far light for 10h;

13.Operating temperature: -10℃ to 50℃;

14.Software functions: Can calculate deflection values, impact coefficient, power spectrum, interval frequency, etc.